Mercurial > repos > blastem
graph
-
Fix Z80 BUSREQ/RESET implementation.Wed, 26 Dec 2012 17:50:24 -0800, by Mike Pavone
-
Fix long reads from IO ports or long reads that trigger sync cycles by saving rdi. Possibly fix word wide IO reads.Wed, 26 Dec 2012 17:34:59 -0800, by Mike Pavone
-
Implement Z80 reset and bus request registers.Wed, 26 Dec 2012 17:06:34 -0800, by Mike Pavone
-
Initial stab at interrupt support. Make native code offsets bigger so I don't have to worry about overflowing the offset. Implement neg and not (untested).Wed, 26 Dec 2012 11:09:04 -0800, by Mike Pavone
-
Add support for indexed modes as a source, some work on jmp and jsr with areg indirect modeSat, 22 Dec 2012 21:37:25 -0800, by Mike Pavone
-
Fix bug in disassembler that caused it to disassemble addresses it shouldn'tFri, 21 Dec 2012 22:33:24 -0800, by Mike Pavone
-
Implement indexed with 8-bit displacement addressing modes in decoder and disassemblerFri, 21 Dec 2012 22:24:45 -0800, by Mike Pavone
-
Added untested support for LINK and UNLKFri, 21 Dec 2012 21:53:05 -0800, by Mike Pavone
-
Removed some old debug printfsFri, 21 Dec 2012 21:26:16 -0800, by Mike Pavone
-
Implement JSR for some addressing modesFri, 21 Dec 2012 21:19:03 -0800, by Mike Pavone
-
Implement DMA (untested)Fri, 21 Dec 2012 20:56:32 -0800, by Mike Pavone
-
Fix some bugs in movem with a register list destinationFri, 21 Dec 2012 16:38:40 -0800, by Mike Pavone
-
Implement a couple of supervisor instructionsFri, 21 Dec 2012 16:04:41 -0800, by Mike Pavone
-
Implement word wide access to IO areaFri, 21 Dec 2012 16:04:30 -0800, by Mike Pavone
-
Implement more instructions and address modesFri, 21 Dec 2012 01:00:52 -0800, by Mike Pavone
-
Make the translator bail out if it hits an instruction I haven't implemented yetThu, 20 Dec 2012 09:17:31 -0800, by Mike Pavone
-
Fix disassembly of reg list in MOVEM when the reg list is the destinationThu, 20 Dec 2012 09:12:24 -0800, by Mike Pavone
-
Fix decoding and disassembly of MOVEMThu, 20 Dec 2012 09:08:13 -0800, by Mike Pavone
-
Fix BTSTThu, 20 Dec 2012 00:56:33 -0800, by Mike Pavone
-
Gamepad supportThu, 20 Dec 2012 00:44:59 -0800, by Mike Pavone
-
Fix issue in which VDP would have trouble emptying FIFO because the VDP cycle count got reset at end of frame.Wed, 19 Dec 2012 22:15:16 -0800, by Mike Pavone
-
Cleanup 68K timing code. Temporarily omment out fFPS counter as it was causing segfaultsWed, 19 Dec 2012 21:25:39 -0800, by Mike Pavone
-
Add FPS counter to console outputWed, 19 Dec 2012 20:53:59 -0800, by Mike Pavone
-
Print out large immediate values in hex rather than decimal formWed, 19 Dec 2012 20:53:45 -0800, by Mike Pavone
-
Add support for BTST instruction (untested), absolute addressing mode for instructions other than move (untested) and fix decoding of MOVEM.Wed, 19 Dec 2012 20:23:59 -0800, by Mike Pavone
-
Fix operand order for AND instructionsTue, 18 Dec 2012 23:55:10 -0800, by Mike Pavone
-
ecx was getting clobbered before the relevant temp value was used in some cases during memory readsTue, 18 Dec 2012 22:56:04 -0800, by Mike Pavone
-
Properly zero-init all VDP buffers. Comment out some debug printfs.Tue, 18 Dec 2012 22:20:25 -0800, by Mike Pavone